Sensors
Shop Tuning Sensors at KingTuner.com
-
LINK Air Temp Sensor (IAT1-8)Easy calibration setup in all LINK Ecu's. Also, It is universal which means it can work with any ECU - not just LINK!Includes 2-pin Deutsch DTM connector kit1/8" NPT Thread
- $112.00
- $112.00
- Unit price
- per
-
LINK 4 Bar MAP Sensor (MAP4)The Link 4 Bar MAP sensor reads up to 4 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 3.0 Bar (or 44psi) of boost pressure. The wiring pinout for this sensor is marked directly on...
- $185.00
- $185.00
- Unit price
- per
-
AEM Bosch Wideband Oxygen Sensor LSU 4.2AEM's Bosch 4.2LSU Wideband UEGO O2 replacement sensor kit includes only the sensor (with attached cable and male connector) and is intended to replace an existing mounted wideband sensor used with AEM wideband air/fuel UEGO controllers. These sensors have a laser-etched, calibrated resistor in...
- $102.95
- $102.95
- Unit price
- per
-
LINK 3 Bar MAP Sensor (MAP3)This Link MAP sensor reads up to 3 Bar absolute pressure. This means that it is suitable for turbo or supercharged applications running up to 2.0 Bar (or 29psi) of boost pressure. The wiring pinout for this sensor is indicated on the sensor.Easy calibration...
- $176.00
- $176.00
- Unit price
- per
-
LINK Ethanol Content Sensor (ECS)Looking to run flex-fuel? Then the Ethanol Content Sensor is a must have. The Ethanol Content Sensor measures the ratio of ethanol to petrol in a flex fuel vehicle. This sensor also measures fuel temperature. Compatible with all current Link Wire-In and Plug-In ECU’s....
- $338.00
- $338.00
- Unit price
- per
-
LINK Oil/Fuel Pressure Sensor (PS150)Easy calibration setup in all LINK Ecu's. Also, It is universal which means it can work with any ECU - not just LINK!Oil or Fuel pressure10 Bar/150psi1/8” NPT ThreadIncludes plug and pin kitUp to 150 PSI above atmospheric pressure, cannot be used to read...
- $289.00
- $289.00
- Unit price
- per
-
LINK Coolant Temperature Sensor (NTC1-8)Easy calibration setup in all LINK Ecu's. Also, It is universal which means it can work with any ECU - not just LINK!Includes 2-pin Deutsch DTM connector kit1/8" NPT Thread
- $80.00
- $80.00
- Unit price
- per
-
AEM Universal 1/8in NPT Air Intake Temp Sensor Kit w/ Deutsch Style ConnectorAEM's Air Inlet Temperature Sensor Kits (AIT) senses the air temperature on the inlet side of the engine.30-2014: Air Temp Sensor with 1/8" NPT Male Thread, High Performance DTM-Style Connector, Aluminum Bung, Connector & PinsFeatures: Senses the air temperature on the inlet side of...
- $86.99
- $86.99
- Unit price
- per
-
Innovate Bosch Wideband Oxygen Sensor LSU 4.2Genuine, new Innovate Bosch Wideband Oxygen Sensor LSU 4.2One of the most critical sensors you'll need. 5-Wire Replacement Sensor For the LM-1 and LC-1
- $147.34
- $147.34
- Unit price
- per
-
AEM Bosch LSU 4.9 Wideband UEGO SensorAEM's Bosch 4.9LSU Wideband UEGO O2 replacement sensor kit includes only the sensor (with attached cable and male connector) and is intended to replace an existing mounted wideband sensor used with AEM wideband air/fuel UEGO controllers. These sensors have a laser-etched, calibrated resistor in...
- $186.19
- $186.19
- Unit price
- per
-
Bosch Knock SensorGenuine, new Bosch Wideband Knock SenorSensor wiring:You must use shielded wire for signal wires, this includes knock sensor signals. Use a 2conductor shielded wire and connect one conductor to the sensor ground pin on the Ecu. Sensor polarity does not matter. Connect the shield...
- $42.00
- $42.00
- Unit price
- per