Products

AEM's Bosch 4.2LSU Wideband UEGO O2 replacement sensor kit includes only the sensor (with attached cable and male connector) and is intended to replace an existing mounted wideband sensor used with AEM wideband air/fuel UEGO controllers. These sensors have a laser-etched, calibrated resistor in...

With our KingTuner Base Map for AEM, you'll get a personalized starting point that includes fuel maps, ignition timing, rev limiters, and idle controls tailored to your engine. We've got all your sensors, inputs/outputs, injector settings, and trigger settings ready to go so you can...

AEM's Air Inlet Temperature Sensor Kits (AIT) senses the air temperature on the inlet side of the engine.30-2014: Air Temp Sensor with 1/8" NPT Male Thread, High Performance DTM-Style Connector, Aluminum Bung, Connector & PinsFeatures: Senses the air temperature on the inlet side of...

Give yourself and your EJ some peace of mind with the ALBERTA RACING ENGINES OEM Oil Pump Upgrade! These pumps are disassembled and cleaned for optimal efficiency. Micro-finished Gerotors and DLC treated relief plungers, these pumps provide reduced friction and reliable operation in all...

Designed for the 3SGE Beams engine in the models specified below.Please check your connector matches the header in the listed photo before purchasing. This ECU works for manual transmissions only. ECU includes an onboard 4 bar or 7 bar MAP sensor Most factory features...

The Link G4X ECU TTLink TTX PlugIn Designed for the VWAG PQ34 1.8l Turbo engine with E-Throttle.This ECU works for manual transmissions only. Includes an onboard 4 bar or 7 bar MAP sensor. Most factory features are supported. Check the features tab for I/O expansion...

5 m long 'B' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilizing Link WireIn ECUs. The 'B' Loom has a Link 'B' ECU connector at one end and unterminated wires at the other. All wires are colour coded...

2.5 m long 'B' loom to suit G4, G4+ and G4X ECUsPerfect for all custom wiring jobs utilizing Link WireIn ECUs. The 'B' Loom has a Link 'B' ECU connector at one end and unterminated wires at the other. All wires are colour coded...

0.4m long 'B' loom to suit G4, G4+ and G4X Wire-In ECUsPerfect for all custom wiring jobs utilising Link WireIn ECUs. The 'B' Loom has a Link 'B' ECU connector at one end and unterminated wires at the other. All wires are colour coded...

This ECU is designed for the E36 M50TUB25 engine. Please check your connector matches the header in the listed photo before purchasing. This ECU only works with the Engine Code M50TUB25 (Bosch ECU from factory).  Works with manual & automatic transmissions.   Built in 4 Bar...

3 port boost control solenoids are the go-to for the majority of boost control applications, they allow for precise control of boost and boost levels can be raised to around 2-3 times the spring pressure of the wastegate.Features: Compatible with all Link and other...

Genuine, new Bosch Wideband Knock SenorSensor wiring:You must use shielded wire for signal wires, this includes knock sensor signals. Use a 2conductor shielded wire and connect one conductor to the sensor ground pin on the Ecu. Sensor polarity does not matter. Connect the shield...

Designed for the 1992-1995 Honda B16 and B18 engine. All models that use the Honda "OBD1" ECU. Please check your connector matches the header in the listed photo before purchasing. This ECU works for manual transmissions only. No onboard MAP sensor.  Knock control is...

Designed for the 1996-1998 Honda B16 and B18 engine. All models that use the Honda "OBD2A" ECU.  Please check your connector matches the header in the listed photo before purchasing. This ECU works for manual transmissions only. Onboard MAP sensor not included Most factory features...

Designed for the K20A engine.Please check your connector matches the header in the listed photo before purchasing. This ECU works for manual transmissions only. ECU includes an onboard 7 bar MAP sensor.  Most factory features are supported.  Check the features tab for I/O expansion options  Note: This Plug-in...

With our KingTuner Base Map for COBB, you'll get a personalized starting point that includes fuel maps, ignition timing, rev limiters, and idle controls tailored to your engine. We've got all your sensors, inputs/outputs, injector settings, and trigger settings ready to go so you...

QTY of 2: Top Hat, 11mm, Blue

QTY of 1: O-Ring, 14mm, Black

QTY of 2: Top Hat, 14mm Blue

QTY of 1: O-Ring, 15mm, Red